...
Step 1: Enable Interzone Replication
Log into MyAccount
Open up the VDC that has the VMs you wish to protect via SecondSite Interzone replication.
Select Replicate with SecondSite Interzone and continue .
Step 2: Order
Select the number of VM's you want to protect and the Zone you want to use as your recovery location (Endpoint)
Purchase
Follow through the payment gateway and confirm your selection.
Step 3: Secondsite Interzone VDC Information
Go back to your MyAccount page and witness that a new VDC with the prefix SS is being provisioned and appears as below.
As you can see it is highlighting a few important items;
Interzone - (Your Protected VDC Name)
Replication - (Number of VMs and VPGs Protected)
Licenses - (Licenses and Extra storage ordered)
Take note - No VM's will be visible under failover vms and your SS VDC till FAILOVER
Step 4: Firewall requirement
Default - If the default NSX-T firewall is sufficient (In most cases) - Go to Step
...
5
Excluded - If you require a BYO firewall, please following the following process
- Log a Ticket at Zettagrid Support - support@zettagrid.com
- Ticket information to Include: Example
Secondsite
...
Number (SS_1175368)
Secondsite
...
Zone (Brisbane)
Account
...
number (214xxxxxx)
Public IPs (
...
Default /31 - More on Request)
Internet
...
Traffic (
...
Data Block or Unlimited per Mbps - Used on failover and can be resized)
Data Block - (100GB - 500000GB)
Mbps - (100Mpbs - 10Gbps)
- Continue with Step
6 while - 5 while waiting for support to create your Internet uplink and public IP
details- assignment
Step 5: Configure your Secondsite Interzone Service
Configure Networks
Log into your SS_ VDC and add networks required
NSX-T Firewall
Live Failovers - Routed Network (Connected to Firewall)
Test Failovers - Isolated Network
BYO Firewall
Live Failovers - Isolated Network (Connected to Firewall)
Test Failovers - Isolated Network
Please note: Secondsite Firewalls
NSX-T or new BYO Firewall - If you have advanced firewall rules or NAT rules setup in your production VDC then you will need to also create these on the new SecondSite instance as it is entirely separate from your production VDC.
Replicated BYO Firewall - Possible config and license changes would be required
Select your VM's to be protected
Go to Manage located on the right of your SS service portal and select Protect VM's
...
Step 6: Confirm Protection
Log into your SecondSite services via MyAccount and confirm Protected VM's and SLA's
Request protection process can take several hours to complete. (Initial Replication and config)
...
Step 7: Failover Process
Test Failover
Start of Virtual Servers in another zone without affecting Production! - Failover via MyAccount Portal
Log into MyAccount https://account.zettagrid.com/
Open up the SecondSite Service under My Services
Select View VPGs
...
Click Start Test on the VPGs you want to failover
Verifying Failover is In Progress (This can take a few minutes)
Verify you
Verify your VM's started
...
Can be seen in MyAccount and Cloud Director
...
...
...
MyAccount
...
...
Cloud Director (Access VM's)
...
Confirm NIC's are connected before testing connectivity
Stop Test Failover
Stop of Virtual Servers in another zone without affecting Production! - Stop via MyAccount Portal
Log into MyAccount https://account.zettagrid.com/
Open up the SecondSite Service under My Services
Select View VPGs
...
Click Stop Test on the VPGs you want to cancel failover
Verify you VM's were removed
...
...
MyAccount
...
Cloud Director
...
...
Live Failover
Start of Virtual Servers in another zone when Production is down! - Can't be performed via MyAccount Portal
Contact Zettagrid Support to perform LIVE failovers! https://www.zettagrid.com/wp-content/uploads/2022/02/ZGSupportCard-v5.4.pdf
Support Phone 1300 597 656 (+61 8 6314 6580)
Support Email support@zettagrid.com
...